backup_jobs - Lists pending and running operations in interactive mode
jobs [-help]
j [-h]
The backup jobs command lists the job ID number and status of each backup operation running or pending in the current interactive session.
This command can be issued in interactive mode only. If the issuer of the backup interactive command included the -localauth flag, the -cell argument, or both, those settings apply to this command also.
To terminate operations that appear in the output, issue the backup kill command and identify the operation to cancel with the job ID number from this command's output.
To check the status of a Tape Coordinator, rather than of a certain operation, use the backup status command.
Prints the online help for this command. All other valid options are ignored.
The output always includes the expiration date and time of the tokens that the backup command interpreter is using during the current interactive session, in the following format:
<date> <time>: TOKEN EXPIRATION
If the execution date and time specified for a scheduled dump operation is later than <date time>, then its individual line (as described in the following paragraphs) appears below this line to indicate that the current tokens will not be available to it.
If the issuer of the backup command included the -localauth flag when entering interactive mode, the line instead reads as follows:
: TOKEN NEVER EXPIRES
The entry for a scheduled dump operation has the following format:
Job <job_ID>: <timestamp>: dump <volume_set> <dump_level>
where
Is a job identification number assigned by the Backup System.
Indicates the date and time the dump operation is to begin, in the format month/date/year hours:minutes (in 24-hour format)
Indicates the volume set to dump.
Indicates the dump level at which to perform the dump operation.
The line for a pending or running operation of any other type has the following format:
Job <job_ID>: <operation> <status>
where
Is a job identification number assigned by the Backup System.
Identifies the operation the Tape Coordinator is performing, which is initiated by the indicated command:
Initiated by the backup dump command. The dump name has the following format:
<volume_set_name>.<dump_level_name>
Initiated by the backup diskrestore, backup volrestore, or backup volsetrestore command.
Initiated by the backup labeltapen command. The tape_label is the name specified by the backup labeltape command's -name or -pname argument.
Initiated by the backup scantape command.
Initiated by the backup savedb command.
Initiated by the backup restoredb command.
Indicates the job's current status in one of the following messages. If no message appears, the job is either still pending or has finished.
For a running dump operation, indicates the number of kilobytes copied to tape or a backup data file so far, and the volume currently being dumped.
For a running restore operation, indicates the number of kilobytes copied into AFS from a tape or a backup data file so far.
The backup kill command was issued, but the termination signal has yet to reach the Tape Coordinator.
The operation is canceled by the backup kill command. Once the Backup System removes an operation from the queue or stops it from running, it no longer appears at all in the output from the command.
The backup command interpreter cannot reach the Tape Coordinator. The message can mean either that the Tape Coordinator handling the operation was terminated or failed while the operation was running, or that the connection to the Tape Coordinator timed out.
The Tape Coordinator has finished the operation.
The operation is waiting for the specified tape drive to become free.
The Tape Coordinator is waiting for the backup operator to insert a tape in the drive.
The following example shows that two restore operations and one dump operation are running (presumably on different Tape Coordinators) and that the backup command interpreter's tokens expire on 22 April 1999 at 10:45 am:
backup> jobs
Job 1: Restore, 1306 Kbytes, restore.volume
Job 2: Dump (user.sunday1), 34 Kbytes, volume user.pat.backup
Job 3: Restore, 2498 Kbytes, restore.volume
04/22/1999 10:45: TOKEN EXPIRATION
None. However, queuing any operation requires privilege, and it is possible to issue this command only within the interactive session in which the jobs are queued.
backup(8), backup_interactive(8), backup_kill(8), backup_quit(8)
IBM Corporation 2000. <http://www.ibm.com/> All Rights Reserved.
This documentation is covered by the IBM Public License Version 1.0. It was converted from HTML to POD by software written by Chas Williams and Russ Allbery, based on work by Alf Wachsmann and Elizabeth Cassell.